High Performance Roundslings

High Performance Roundslings are constructed using a continuous loop of UHMPE core yarns encased in a texturized nylon, double wall cover. This heavy duty cover helps to protect the load bearing core yarn from abrasion and increase the life of the sling.

Vertical, Choker & Basket Hitch
Load bearing points can be rotated to extend life
Lightweight: Ease of use compared to wire rope and chain
Low Stretch: Approximately 1% at rated capacity
Highest capacity for the lightest weight
Texturized Nylon Double Wall, Seamless Cover
- Helps protect core yarn from UV degradation
- Soft cover helps to prevent scratches to load surface
Two sliding wear sleeves standard on all BHP slings

High Performance Roundsling Catalog

Size	Vertical	Choker	Basket At 90°	Basket At 45°	Min. Length	Body DIA Relaxed (in.)	Width at Load (in.)	Weight Per Foot (lbs.)	Min. Hardware Diameter (in.)	Min. Edge Radii (in.)
BHP10	10,000	8,000	20,000	14,100	4'	1	1.6	0.45	0.69	0.43
BHP20	20,000	16,000	40,000	28,000	4'	1.25	2	0.55	1.06	0.63
BHP30	30,000	24,000	60,000	42,000	6'	1.4	2.13	0.7	1.44	0.75
BHP40	40,000	32,000	80,000	56,000	6'	1.75	2.75	0.82	1.5	0.88
BHP50	50,000	40,000	100,000	70,000	8'	1.9	2.88	1.02	1.75	0.88
BHP60	60,000	48,000	120,000	84,000	8'	2	3.13	1.15	2	1
BHP70	70,000	56,000	140,000	98,000	8'	2.15	3.25	1.29	2.19	1.13
BHP80	80,000	64,000	160,000	113,000	8'	2.25	3.5	1.5	2.38	1.25
BHP90	90,000	72,000	180,000	127,000	10'	2.5	3.88	1.64	2.38	1.25
BHP100	100,000	80,000	200,000	141,000	10'	2.75	4.25	1.77	2.5	1.38
BHP125	125,000	100,000	250,000	176,000	10'	3	4.88	2.15	2.63	1.5
BHP150	150,000	120,000	300,000	210,000	10'	3.25	5.25	2.49	2.88	1.5
BHP175	175,000	140,000	350,000	240,000	10'	3.5	5.75	3.12	3.13	1.75
BHP200	200,000	160,000	400,000	280,000	10'	3.75	6.13	3.46	3.38	1.75

WARNING: Do not exceed rated capacities. Sling capacity decreases as the angle from horizontal decreases. Slings should never be used at angles less than 30 degrees.

Manufacturing Tolerance (applies to roundslings when new, at the time of final manufacture):

30,000 lbs. or less – +/-1” + 1% of specified length and applies to roundslings when new, at the time of final manufacture.
Higher than 30,000 lbs. up to 90,000 lbs. – +/-2” + 1% of specified length and applies to roundslings when new, at the time of final manufacture.
Higher than 90,000 lbs. up to 175,000 lbs. – +/-3” + 1% of specified length and applies to roundslings when new, at the time of final manufacture.
Higher than 175,000 lbs. – +/- Sling Body Diameter + 1% of specified length and applies to roundslings when new, at the time of final manufacture.

Matched Set Length Tolerance – When multiple legs of a bridle sling are made, or when multiple slings are prescribed to be made within a Matched Set Tolerance, their length variance from their nominal length shall remain within a dimension equal to one-half of their corresponding Standard Length Tolerance Values.

Measurement Method – Roundsling length is measured with the sling laid flat while being manually pulled taut.

Phone

Email

High Performance Roundslings